Colour blocked background with a new greeting and some leaf die cuts

One of the last kits to be finished off from my desk.   I used this colour blocked background and relegated the chalk board greeting to my stash.  I added the embossed background to a green card front and went looking for a greeting.  I found this laser printed one (Beccy's Place) which I have found difficult to include in my cards for some reason but it worked perfectly for this card.  I trimmed the greeting and flagged both ends, layered it onto yellow and flagged both ends again before watercolouring the flower and leaves.  I mounted this greeting with a bit of 3D foam tape in the middle and double sided taper on both ends which gives just the right amount of dimension and allowed me to tuck in my leaf die cuts.  I die cut the leaves (SU) from white cardstock and tuck a full one above the greeting and trimmed off the leader from the other and tucked it below the greeting.  I glued them in place with white glue applied with my fine tip applicator.  I love how it turned out!!!!!              Therese

Cards with fun collaged washi tape backgrounds embellished with 3D layered elements

 I have decided to make several sets of cards to give as gifts and was really pondering what I should use as my backgrounds and if I should include any greetings.  Cards without greetings are always more versatile in that they will be appropriate for more occasions but they need good sketches to work.  Because I had washi tape sitting on my desk I decided to play a little and see if I could make up a few backgrounds.  In an effort to reduce the size of my paper stash I wondered if it would work to use decorative scrapbook paper for my backgrounds.  I went looking through my stash and found a few sheets that I thought might work as they were somewhat subtle in pattern and intensity of colour.

So I cut up this sheet of paper - a checkered background with quite a few different colours finely spattered over it.  Next, I checked out my washi tape supply and found a few that worked reasonably well with the paper.  I simply cut or tore the washi tape into strips and applied them to my trimmed pieces of decorative paper.   While, I was at it I made four sets of backgrounds using four sheets of decorative paper.  I put those to press and started dreaming up some embellishments that would be substantial enough to balance the backgrounds I had created, large enough that they would not need greetings and versatile enough in subject matter that they would be appropriate for more than one occasion.  I started by digging out any dies I had that fit the bill as to size and subject matter - hearts, flowers, butterflies, birds, etc.
For my first, card I layered three different sized hearts. The large one is a die cut (CB), the middle one is an embossed heart die cut (SU) and the final one is die cut (SX) cut from white solid core cardstock which I embossed and sanded.  I put just a bit of glue between them to hold them in place and machine stitched them to each other adhering the thread ends to the back with regular tape.  I glued my background to an off white card (a bit smaller than A2) and then adhered my 3D embellishment to the card front using 3D foam tape.  That worked pretty well!!  Now the challenge was to see if I could come up with a few more embellishments that worked as well.
For my second card, I cut a maroon flower (SX), manually embossed it with the Swiss Dot embossing folder (CB) using a hammer, added a manually embossed circle in the center then two leaf punchies which were also manually embossed and mounted this focal element to my card front to which I had already mounted my washi tape background.
For my third card, I mounted my washi tape background to my off white card and then worked on my embellishment. I cut this paisley pattern (SX) from both dark pink and yellow.  I swapped the pieces to create a yellow paisley with a dark pink heart and a small yellow heart and secured them with tape on the back.  The holes were too hard to situate so I simply cut a dark pink shape that was just smaller than the whole and glued it to the back and shows in all the holes.  Decided that it looked a bit like a cute bird with a heart wing and added a tiny black brad for an eye, a tiny brown triangle for the beak, swirly wire tail feathers and mounted it to my card front using 3D foam tape.  Finished it off by adding two legs with a black permanent marker!!
For the fourth card in this set, I die cut a butterfly (SX) from yellow cardstock and overlaid a paper butterfly that I had in my stash and to finish it off added a body and antennae that I die cut (QK) from a butterfly die set.  I glued them together just in the middle so the wings would be free to flutter.  Added it to my layered card front using 3D foam tape and used a black permanent marker to add a dotted flight path.
I am pretty happy with how this set of cards turned out!!  So I will continue to work on my other card sets and will share them here as I finish them up!!

Therese