Contact me

Tuesday, November 03, 2020

A Minecraft birthday card featuring a square background and black face, a little Minecraft Lego man and a stony birthday greeting

Made this card for my grandson on his birthday!!  He is a Minecraft fan as was his sister when she was that age.  I had a friend request a Minecraft card kit a while back and so I had already developed the pieces I would need for this card.  The grid background is one I found on line and trimmed to the size I needed for my card.  I cut the black pieces as I needed them to create the face.  The little Lego Minecraft guy was downloaded off the internet, sized and printed before being fussy cut.  I applied ink to his edges to ensure that no white showed.  The greeting is another one I found on line.  I sized it and printed it for my card.  I added an orange line to my background after I trimmed it.  I used 3D foam tape to add the black pieces to my background.  I adhered the background to a green card.  I trimmed my greeting to size, flagged the end and then distressed all the edges with my distress tool.  Wanting it a little less crisp I sponged the edges with black ink to just tone it down a bit.  I glued the greeting below the background and then added the little man using 3D foam tape.  He looked like he was walking on air so I added some stippling with a marker to simulate the ground.  I really like how it turned out.  Therese
 

An all occasion card featuring a die cut deer and evergreen tree, torn paper and some coordinating fiber

Another all occasion card which would work very well for Christmas or a birthday.  I started with a kraft card and added a kraft and green paper background.  I tore the top off of a brown cardstock rectangle to create a foreground and added it to my card gluing only on the bottom edge to allow me to tuck the tree and deer in behind.  The deer was sent to me by a friend and I embossed it to give it a bit of texture.  I mounted the tree with double sided tape and the deer with 3D foam tape.  The top area needed a bit of "something" so I added some fiber secured on both ends using with a half circle of kraft cardstock.  This way of securing fiber worked quite well and leaves the inside of your card clean.  I tied on another little piece to give my card a bit more texture.  

Therese
 

Birthday card featuring an embellished decorative paper background, ribbon and a watercoloured landscape

Birthday cards for family were made up this week!!  For this card I started with a gray card.  The background striped and plaid paper have been in my stash for a while and were just too stark to be used so I decided to embellish them a bit.  I added watercolour in green and blue and then stamped green trees in an all over pattern to the both of them.  I trimmed the striped on and added a piece of plaid one below and added a green ribbon over when they join.  I adhered this large background to my card front.  I sized, printed, trimmed and watercoloured the landscape digital image (CLKER) to coordinate with my background.  I cut a black rectangle to back it and when I came to layer them I decided to offset them instead of layering them symmetrically.  Works - I should do it more often.  I mounted this focal element to my card using 3D foam tape.  It is already on its way!!!!

Therese 



 

Christmas card featuring a little gift, a stamped background and decorative paper and a font greeting

This card was created while I was working out samples for this card for my Christmas card kits.  I had all sorts of pieces I tried out and finally once the design was finalized I decided to make up cards with what I had sitting on my desk.  For this card I trimmed the gift from sticker packaging I have hand on hand for a while.  I cut it square (2 1/8") and added a white ribbon from top to bottom and an embossed flower for the bow.  It was not too bad but the ribbon did not go with a lidded box and the embossed flower did not have enough detail for what I was looking for.  I did add a silver flower outline between them and that was much better.  I stamped my maroon card front with a distressed background stamp (SU - Worn) with red ink.  I trimmed the triangle from a red paper with glittery swirls.  The greeting was laser printed and I added texture with my pattern tracing wheel before trimming it to size and flagging the end.  I glued the triangle leaving the  top loose, added my greeting and then glued the top down.  I added the gifts using 3D foam tape to finish off this card.  I have another triangle of this glittery paper so I will probably make one more for my stash.  I have not made cards for myself yet this month.           Therese